Go-ped Know-Ped Bedienungsanleitung PDF herunterladen (Seite 9)

WARNING: Patching a tube is an emergency repair. Patches can severely weaken

the integrity of a tube, resulting in possible tube failure and cause a loss of control.

Replace a patched tube as soon as possible. Never replace the tube with anything

other then the stock OEM tube. Using an aftermarket tube or tire not intended for

Go-Ped® specification could result in a sudden loss of pressure that could cause

damage to your scooter and sudden loss of control. Never use a tube or tire that is

not recommended by Go-Ped®.

CAUTION: Replace front or rear tires when tread is worn within 1/16" tread depth,

or if obvious tire damage has occurred.

D. Non-Pneumatic Tire Information

Non-pneumatic tires require no maintenance but must be replaced when normal wear and tear makes

the tire diameter reach the wear limit dimple found on the side wall of the tire. Split, cracked or torn

tires should be replaced immediately.

E. “T” Handle Installation

1. Remove the plastic hinge pin from the bottom of the handle bar assembly.

2. Compress slide tube locking spring and hold in place.

3. Insert the handle bar assembly in the slot of the lower hinge assembly found on the body of the

frame assembly at the front fork.

4. Hold the slide tube in the up position and insert the plastic hinge pin.

5. Use a hammer and a spare bolt (not provided) to get the plastic hinge pin centered in the hole so

that the slide tube can slide over it and sit flush with the bearing race. Note: Refer to “3.4 Folding

Feature” for proper operation.

3.3 Go-Quad®, Super Go-Quad™.

Your Go-Quad® kart is shipped with the seat and butterfly steering wheel disassembled. It is

recommended that you ask your dealer for assistance in the final set up of your cart.

A. Installing butterfly steering wheel.

1. Line up Steering wheel to holes on steering column.

2. Use the (3) 7/16” bolts to install steering by inserting the bolts through the 3 holes in the steering

wheel.

3. Place the washers over the steering bolts and finish by installing and tightening the nuts.

B. Installing the seat

1. Line up seat to seat holes in frame.

2. Use the shorter 1/2” bolts with washer for the rear seat. Install bolts finger tight.

3. Use longer bolts with washer for the front. Insert (2) stacked rubber dampeners/spacers between

frame and seat and then insert the bolts into the seat.

4. Tighten the four seat bolts to finalize.

3.4 Folding Feature

Your Scooter is equipped with a folding feature for easy carrying and stowage. To fold pull up against

the spring tension on the slide tube found on the base of the “t” handle until it completely exposes the

hinge assembly and fold to the latching mechanism found next to the motor. Reverse process to lock

handle bar in the riding position. Note: Karts do not have a folding feature.

A. Adjustment of Slide Tube Clamp:

The slide tube clamp on the bottom of your Pro Slide Tube is used on extreme performance Go-Peds

to reduce handlebar play at the hinge. Adjustment of the clamp is a simple operation, which is

performed using a 5mm allen wrench.

-If the clamp is left loose, the slide tube can easily slide up so that the scooter may be folded.

-If the clamp is very tight, it will not be possible to slide the tube up and fold the scooter.

-The clamp will reduce play even when the bolt is not very tight. The play will be reduced more as the

bolt is tightened.

-The rider should determine the setting which works best for them.

6.6 Motorized Riding

Warm up the engine (30 seconds to one minute). With the Sport, X25, X-Ped®, and Super X-

Ped™ engine running and with throttle set at idle, set the rear tire on the ground and immediately

start walking alongside the scooter then step on the deck with both feet and with both hands

firmly on the handle grips you can now begin to add throttle control. This will take some practice

and coordination before you can do it smoothly. With the GSR® you simply stand on the scooter

with both hands on the controls, release the brake, it will begin to roll and you can now apply

throttle control. With the Bigfoot™ and Go-Quad® you have both hands on the controls and push

off or get a push from an assistant. While the scooter or kart is rolling, slowly lower the motor

using the trim lever to engage the drive spindle against the tire while slowly applying more

throttle.

WARNING: The scooters and kart outlined in this manual use a friction and/or a

chain drive system. Keep clear of rear wheel and its drive components when the

engine is running or sever injury may occur.

CAUTION: As engine power is applied through a friction or chain drive, it is very

important to maintain proper drive roller/chain tension adjustment as outlined in

this manual.

Section 7: Free Wheel Scooting

7.1 Sport, S25™, X25™, X-Ped®, and Super X-Ped

Unlock the rear wheel quick release lever. Pull wheel down to bottom of axle adjustment slot. Rotate

EPW to contact lug and lock down Quick Release Lever. Check for free rotation of rear wheel. Riding

in this mode should be legal anywhere bicycles are allowed.

NOTE: Rear wheel adjustment will be required more frequently when tire is new, to prevent drive

system slippage. If drive system is allowed to slip excessively, high temperatures will result and

damage the drive spindle, extreme or uneven tire wear will also result, causing uneven overloading to

engine crankshaft and bearing. Refer to section 9.3 “Adjusting the rear wheel” in this manual to

correct drive system engagement issues.

7.2 Bigfoot™ Go-Quad® and Super Go-Quad™

To disengage the drive system for free wheeling simply adjust the engine trim lever to the disengaged

position.

7.3 Chain Drive Units: GSR Models

With engine not operating simply push the scooter. Note: there will be some resistance caused

by the chain components.

Section 8: Maintenance and Parts

CAUTION: Technological advances have made Go-Ped® and the components

more complex then ever. This on going evolution makes it impossible for this

manual to provide all the information required to properly repair and or main-

tain your Go-Ped®. In order to help minimize the chances of an accident and

possible injury, it is critical that you have any repair or maintenance which is not

specifically described in this manual performed by an authorized Go-Ped® dealer.

Just as important is that your individual maintenance requirements will be determined by everything

from your riding style to geographic location. Consult your authorized Go-Ped® dealer for help with

determining your individual maintenance requirements.

1 2 3 4 5 6 7 8 9 10

Kommentare zu diesen Handbüchern

Keine Kommentare

Go-ped Know-Ped Bedienungsanleitung Seite 9

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Zubehör für elektrische Go-ped Know-Ped